WELCOME TO Competition Distributing Inc. / Parts Catalog

Back To Main Parts Index / Back Technical Index / Print Your FAX Form HERE.

Technical Page 55:

Technical: Page 53 / Page 54 / Page 55 / Page 56 / Page 57 / Page 58 / Page 59 /
Page 60 / Page 61 / Page 62 / Page 63 / Page 64 / Page 65 / Page 66 / Page 67

What Your Equipment Is For

1. Envelope containing your registration card, which should be filled out and sent to the factory immediately upon delivery of your machine.

2. Envelope containing four washers for changing the adjustment of the mechanical oiler, as given in the instructions on pages 35 and 36. Two thick washers BO-320. Two thin washers BO-280. Spark plug adjusting gauge EK-1091 is also in this envelope.

3. Extra inner tube valve cap DX-146.

4. Extra inner tube valve plunger DX-148.

5. Envelope containing valve parts.

6. Envelope containing powdered mica. Mica to be spread over repair after repair is completed to prevent tube or casing from sticking to repair.

7. Inside blowout patch for temporary repair of casings. To repair a small cut in the casing, cut a large enough piece from the roll.

8. Emery paper for cleaning the inner tube when a repair is necessary.

9. Cap EO-747 to screw on oil tank nipple when feed line is disconnected.

10. Tool box key DJ-721B, for electrically equipped model.

11. Keys AJ-505A, for tool box on magneto model.

12. Cementless patch for repairing inner tube. To repair a punctured inner tube cut a large enough piece from the patch to cover the puncture.

13. Container for articles supplied with tire kit.

14. Chain tool GK-739, for making repairs to the drive chain.

15. Wrench AK-2, for rear axle adjusting screw lock nuts.

16. Wrench AK 2, for rear axle adjusting screws and carburetor low speed adjusting screw.

17. Wrench DK-38, for pedal pin.

18. Wrench DK-38, for carburetor gasoline pipe nut.

19. Adjustable pliers AK-269.

20. Screw driver CK-270.

21. Wrench GK-65, for exhaust valve lifter pins, inlet push rod lock nut and all 7/16 inch hexagon nuts.

22. Wrench GK-65, for exhaust valve spring cover.

23. Monkey wrench DK 809, for general use.

24-25. Wrench, FK-822, for inlet housing clamp nuts and crank case stud nuts.

26-27. Wrench DK-805, for clutch pull rod adjusting nut and lock nut.

28. Wrench DK-807, for nuts holding the transmission onto frame.

29. Double repair link DK-316, for repairing the drive chain.

30. Coupling link DK-712, for use when only a coupling link is broken.

31. Half link DK-315, to be used when chain does not require a full link.

32. Bosch Magneto Wrench AK-424, supplied with those models equipped with a Bosch magneto.

33. Berling Magneto Wrench GX-1621, supplied with those models equipped with a Berling magneto.

34. Wrench DK-815, the flat steel strip is a gauge to be used when adjusting the circuit breaker points, as mentioned in the instructions covering the care of the Remy generator. The notched blade is used to tighten the nuts holding the cables to the coil. The wrench is for adjusting the circuit breaker points.

Back To Main Parts Index / Back Technical Index / Print Your FAX Form HERE.

CLICK IMAGE TO ENLARGE

Print Your FAX Form HERE.

ORDERS: UPS orders welcomed.
Prefer orders being FAXed to us, or email
except when technical advice is required.
VISA, MC and Discover Cards are welcomed.
2106 Lazelle St. Sturgis, SD 57785
(605) 720-1903 * FAX (605) 720-1929
Email: competitiondist@earthlink.net
Alternate: competitiondist@rushmore.com